SA05 rod probe for tracing 512Hz sondes (green, see image below).
Tracing distance 30cm…10mg

Dimensions & weight
SA05: 156 x 23 x 20 mm, approx. 105g

Protection class
IEC 60529 IP44 when attached to the receiver

Environmental conditions
Usage -40…+60ºC (dry or moist conditions), storage
-40…+60ºC (dry conditions)

The post SA05 – ROD ANTENNA FOR COMPACT LOCATOR appeared first on FiberOptics24.eu.

SA43 rod probe to locate sondes and underground cables. Operates on 33kHz and 10kHz frequencies.
Tracing distance 30cm…10m

Dimensions & weight
SA43: 156 x 23 x 20 mm, approx. 90g

Protection class
IEC 60529 IP44 when attached to the receiver

Environmental conditions
Usage -40…+60ºC (dry or moist conditions), storage
-40…+60ºC (dry conditions)

The post SA43 – ROD ANTENNA FOR COMPACT LOCATOR appeared first on FiberOptics24.eu.

CL43 Compact Locator is an affordable and easy-to-use wire and cable and duct sonde locator.
Outdoors CL43 can be used to trace and pinpoint underground cables and sondes in several meters depth.
Indoors CL43 can be used to locate for example floor heating cables and wires inside walls.

CL43 has a simple user interface with only two buttons, 13 LED lights and a speaker. Probes are easy to
disconnect therefore it easy to carry the receiver and a probe even in a pocket. CL43-PB kit does not include
a transmitter, however, it is compatible with all Vesala 512Hz sondes PL18-05 and PL42-05. 512Hz is intended
especially for tracing metal ducts, such as cast iron.

Other Vesala duct sondes operate at 10kHz and 33kHz (See Duct Sondes on Accesories page) and the compatible CL43
product setup is CL43-PA.

Additional probes for CL43 can be acquired also later. If you would need a setup to trace cables and wires
indoors and outdoors, look at the CT33 cable tracer. We will build a setup according to your preference
including probes and duct sondes, all packed in a handy case.

Set consist of:

• Compact Locator CL43
• Receiver probe SA05 (512Hz)
• Carrying case KLCL43
• User manual
• Batteries

PRODUCT INFO SHEET PDF.

The post COMPACT LOCATOR CL43-PB KIT appeared first on FiberOptics24.eu.

Tracing Probe:

• Plastic probe tip prevents accidental shorts
• LED light provides a visual indication of signal strength
• Able to check the polarity of many 6P2C/4P2C telephone jacks
• Adjustable volume knob and headphone jack assist in tracing wires
• Works with many other manufacturers’ analog tone generators
• Includes 9V battery required for operation

Tester & Tone Generator:

• Remote terminator can be used to test RJ45 cables with ease
• Provides tone via RJ45 and BNC connectors or test clips
• Provides talk power to a telephone for testing
• Two different musical tones to choose from
• Works with our TEP-200 tracing probe or others to identify cables
• Includes TET-6 Accessory Kit and 9V battery required for operation

This kit includes:

• TET-700 Multi-Function Cable Tester & TonerUSER MANUAL PDF.
• TEP-200 Tone Tracing Probe
• TET-6 Accessory Kit for TET-700PRODUCT DATA SHEET PDF.
• (2) 9V batteries

The post TETP-900: Multi-Function Cable Tester Tone & Probe Kit appeared first on FiberOptics24.eu.

PRODUCT INFO SHEET PDF.

PRODUCT INSTRUCTION SHEET PDF.

The post MCT-468: Modular Cable Tester for RJ45, RJ12, RJ11 Cables appeared first on FiberOptics24.eu.

WARNING:

Read the manual before operating or servicing this tool. Failure to understand how to safely
operate this voltage tester may result in serious injury or death.

PRODUCT INFO SHEET PDF.

INSTRUCTION MANUAL PDF.

The post VT-1000: Non-Contact Voltage Tester 90 to 1000VAC appeared first on FiberOptics24.eu.

CL43 Compact Locator is an affordable and easy-to-use wire and cable and duct sonde locator.
Outdoors CL43 can be used to trace and pinpoint underground cables and sondes in several meters depth.
Indoors, the CL43 finds very easily for example, underfloor heating cables and wires inside the walls.

CL43 has a simple user interface with only two buttons, 13 LED lights and a speaker. Probes are easy to
disconnect making it easy to carry the receiver and a probe even in a pocket.

CL43-PA kit does not include a transmitter but it is compatible with all Vesala 10kHz and 33kHz transmitters
(CTT33) and duct sondes (See Duct Sondes on accessory page). CL43 also works with other manufacturers’ 33kHz
transmitters.

Especially for tracing cast iron ducts a product setup CL43-PB is available. Corresponding 512Hz sondes are
PL18-05 and PL42-05.

Additional probes for CL43 can be acquired also later. If you would need a setup to trace cables and wires
indoors and outdoors, look at the CT33 cable tracer. We will build a setup according to your preference
including probes and duct sondes, all packed in a handy case.

Set consist of:

• Compact Locator CL43
• Receiver probe SA43 (10 kHz and 33 kHz)
• Carrying case KLCL43
• User manual
• Batteries

PRODUCT INFO SHEET PDF.

The post COMPACT LOCATOR CL43-PA appeared first on FiberOptics24.eu.

Vesala’s PK2 Drill Point Locator set solves the repeated problem how to drill holes through walls,
floors etc. safely and accurately. With PK2 time consuming measuring or using trial & error
drilling to find the right drill location can be avoided. PK2 includes transmitter PKT2 and receiver
PKR2.

Corresponding location on the other side is located with the receiver. The arrow LED indicators of
PKR2 show and distance display reading gets smaller. Green rectangular LEDs appear when the right
spot has been reached. Right spot can be pinpointed accurately up to 150cm distance.

Before drilling it is often good to know whether there are hidden obstacles in the way. PKT2
transmitter has an automatic metal detector feature, which warns if there is metal under it. AC
detector displays if there is alternating voltage present, hinting about possible live mains
wiring underneath.

PRODUCT INFO SHEET PDF.

The post DRILL POINT LOCATOR PK2 appeared first on FiberOptics24.eu.

Cable tracer TM30 is a cable & wire tracer equipped with monitoring and measuring properties.
It can be used also at mains environment, so it is well suitable for both telecom and electric
installation work as well as renovation and fault spotting work and much more.
With TM30 it is also possible to trace short length wires or single wires, which are usually hard to find.

Transmitter TMT30
TMT30 has three very easy to use operating modes:

• In the Trace mode device transmits a signal to be traced with the receiver. TMT30 withstands
  voltages up to 400V, so it can be well plugged into e.g. a mains wall socket. Device also displays the
  voltage at the outputs and the feeding signal current to the target.
• In the Meter mode, TMT30 operates as a voltage and frequency meter.
• With a special DSLAM test TMT30 can be used to check whether a CO side ADSL modem is present
  on a seemingly unused line.

Receiver TMR30
TMR30 is very versatile:

• It has three Trace modes to be used to trace and track signals generated by the transmitter on PRODUCT INFO SHEET PDF.
  open wires or cables. Cables can be traced from close ranges up to several metre distance.
• The three Monitor modes can be used to monitor, or listen, signals over wires or terminals
  without galvanic contact to them.
• With the Powerline monitor mode TMR30 can be used without the transmitter to reveal live USER MANUAL PDF.
  wires and wall sockets and which side is phase.
• High frequency signals, such as broadband wires and terminals, can be monitored with
  the High Freq mode.
• With the Audio freq mode audio frequencies can be listened right at the surface of wires.

TMR30 has fixed internal antennas so it is very compact and easy to use. The LED bar display together
with the audible signals reveal the traced target while tracing. Furthermore TMR30 has an optional
LED work light pointingto the traced spot.

The post Cable Tracer TM30 appeared first on FiberOptics24.eu.