The post BATTERY FOR PL18 SONDE appeared first on FiberOptics24.eu.

The post BATTERY (10 PCS) FOR MPL7 AND MPL9 SONDES appeared first on FiberOptics24.eu.

The post BATTERY (10 PCS) FOR MPL4 AND MPL6 SONDES appeared first on FiberOptics24.eu.

MPL6-33 is a separate and very small size microduct microsonde. Especially intended to be used with the Vesala CL43 Compact PRODUCT INFO SHEET PDF.
Locator, also other cable tracers and pipe locators using the 33kHz tracing frequency. This transmitter microsonde is especially
suitable for tracing blockages of optical cable’s microducts as well as tracing other small non-conductive pipes and sewers.
MPL6-33’s diameter is only 6.4mm so it fits into the standard 12/8mm tubes.SONDE SPETCIFICATIONS PDF.

MPL6-33 construction includes the transmitter unit and battery compartment connected together with a semi-rigid
middle part. The shape of the transmitter and the unique construction help the sonde pass tube curves and joints more easily.USER MANUAL PDF.

Working with MPL6-33

Microsonde turns on and starts sending tracing signal when a battery is inserted and the battery compartment is turned to the
middle part. The sonde is attached to the tip of a push rod by its M5 female thread. Which are located at the end of the battery
compartment. Alternatively the sonde can be taped to the side of the push rod to reduce risk of damage. Sonde can also be
attached to the tip of an optical cable. After which the sonde is jetted into a microduct together with the cable.

If there is a blockage in the microduct. Firstly, location can be roughly estimated using the jetted cable or rod length and
cable & duct maps. After that, the exact location of MPL6-33 is traced in the area above ground with a cable tracer
receiver. In conclusion, knowing the exact spot of a blockage considerably saves time and reduces unnecessary digging costs.

Other usage and batteries

Both the transmitter unit and the battery compartment are watertight enabling underwater use. There is a blinking light at
the tip of the transmitter indicating transmitter operation. Lithium battery gives approx. 9 hours total usage time depending
on ambient temperature.

MPL6-33 diameter is 6.4mm and length with mounted battery compartment 84mm.

Transmitter signa

32.768 kHz continuous sinusoidal signal.

If you need also Shock Absorbers please check compatibly here and make a Request Qoute

Made in Finland

The post MICROSONDE MPL6-33 (6.4 MM, 33 KHZ) appeared first on FiberOptics24.eu.

PRODUCT INFO SHEET PDF.

Transmitter sonde PL18-33 is a small pipe transmitter sonde which is an efficient accessory for the Vesala
CL43 Compact Locator and other cable tracers and pipe locators using the 33kHz tracing frequency.

Using a pipe transmitter sondeSONDE SPETCIFICATIONS PDF.

PL18-33 powers on when the battery compartment is turned to the transmitter section. Sonde can attached
to the push rod (snake) at first, with the threaded sleeve of the battery compartment and secondly, with tape.
After that the sonde isUSER MANUAL PDF. pushed into the target pipe using the push rod.

To avoid loosing signal e.g. at corners the sonde is traced with a cable tracer receiver along as it moves ahead.
If sonde hits an obstacle or blockage, it´s possible to define the location and depth very accurately, which
reduces unnecessary digging.

PL18-33 has a red power-on LED at the end of the sonde. LED goes off if battery is weak. PL18-33 diameter is
18.2mm and length with standard battery compartment 85mm. Transmitted signal is continuous 32.768 kHz.

The post TRANSMITTER SONDE PL18-33M10M and M12F (18 MM, 33 KHZ) appeared first on FiberOptics24.eu.

The duct holder is an optional accessory to the for Hexatronic ABF Installation Tool LTT1792040 and LTT1792011.
It enables a secure grip of the duct so that the duct won’t get loose even when high air pressure is used for long
distance blowing. The duct holder also facilitates the installation since the duct can be attached to the blowing
tool even when the main body of the tool is in open position. This is especially handy when blowing fibers that are
pre-terminated with a connector ferrule.

The post Duct Holder for ABF Installation Tool appeared first on FiberOptics24.eu.

LA43 close range probe for tracing and identifying cables (accessory). Operates on 33kHz and 10kHz frequencies.
Tracing distance 0cm…30cm

PRODUCT SHEET PDF.

The post Inductive Puck Antenna LA43, For CL43 appeared first on FiberOptics24.eu.

Loading a protection sleeve onto a fiber can be tedious even, for the most experienced technicians.PRODUCT DATA SHEET PDF.
In addition, if they have physical impairments such as poor eyesight then it can become nearly impossible.
QuickSleever is designed sleeves loading  onto fiber quick and easy. The PSI-15 tool is ideal for aligning APPLICATION NOTE PDF
fiber to the holes of protection sleeves and is a real timesaver.

Our PSI-15 won the 2020 Cabling Installation & Maintenance Silver award for innovation! (See it here)

The post PSI-15: QuickSleever™ appeared first on FiberOptics24.eu.

PRODUCT DATA SHEET PDF.
VFL-25125 FC/LC designed to convert the VFL-25 (or other similar VFLs) from FC to LC, this VFL Adapter is perfect for
detecting faults in LC connectorized cables.

Included in VFL-150 Visual Fault Locator Kit

The post VFL-25125: FC to LC Adapter appeared first on FiberOptics24.eu.

MegaSonde PL42-05 is Vesala’s most powerful sonde particularly for metal ducts. The sonde
has an M12 thread in their battery compartment end for push rod mounting. PL42-05 is packed
in a small carrying/storage case including 8 pcs AA/LR6 batteries.

This Vesala product is made in Finland.

SOND BROCHURE PDF.

SONDES SPECIFICATION PDF.

The post MEGASONDE PL42-05 (42 MM, 512 HZ) appeared first on FiberOptics24.eu.