No products in the cart.
DRILL POINT LOCATOR PK2
- For pinpointing drill holes through up to 150cm concrete walls and floors
- For determining required drill depth
- For detecting metal and electric obstacles
COMPACT LOCATOR CL43-PB KIT
Locator CL43-PB Kit with rod probe SA05 (512Hz)
- Affordable receiver especially for locating duct sondes
- Also compact wire and cable locator
- Supports 33kHz, 10kHz and 512Hz frequencies
- For outdoor and indoor use
Cable Tracer TM30
- Traces cables and wires, also live wires up to 400V
- Identifies wires and pairs and circuit breakers
- Monitors telecommunication lines
- Locates metal tubes and ducts
COMPACT LOCATOR CL43-PA
LOCATOR CL43-PA Kit with SA43 rod probe (33kHz and 10kHz)
- Affordable receiver especially for locating duct sondes
- Also compact wire and cable locator
- Supports 33kHz, 10kHz and 512Hz frequencies
- For outdoor and indoor use
SA05 – ROD ANTENNA FOR COMPACT LOCATOR
SA05 – ROD ANTENNA FOR CL43 COMPACT LOCATOR, 512 HZ
SA43 – ROD ANTENNA FOR COMPACT LOCATOR
SA43 – ROD ANTENNA FOR CL43 COMPACT LOCATOR, 10 KHZ AND 33 KHZ
TETP-900: Multi-Function Cable Tester Tone & Probe Kit
Kit includes:
- TET-700 Multi-Function Cable Tester & Toner
- TEP-200 Tone Tracing Probe
- TET-6 Accessory Kit for TET-700
- (2) 9V batteries
VT-1000: Non-Contact Voltage Tester 90 to 1000VAC
JONARD
- Non-contact voltage detection from 90-1000 VAC
- Tests wires and cables through insulation as well
- CAT IV 1000V rating for added operation and protection
- LED light and beep sound to indicate that voltage is detected
- Optional silent mode for use in quiet areas
- Compact and lightweight design with built-in pocket clip allows you to carry it on the go
- Automatically shuts off after 3 minutes to preserve battery life
- Powered by (2) AAA batteries (included)
MCT-468: Modular Cable Tester for RJ45, RJ12, RJ11 Cables
JONARD
- Tests RJ45, RJ12, and RJ11 terminated cables with ease
- Tests for opens, shorts, and miswiring
- Full LED indication lights on both main and remote unit
- Automatically tests when switched on
- Can slowdown testing procedure using “S” switch to better see each test
Includes: Nylon carrying case and 9V battery (for use)
DRILL POINT LOCATOR PK2
- For pinpointing drill holes through up to 150cm concrete walls and floors
- For determining required drill depth
- For detecting metal and electric obstacles
COMPACT LOCATOR CL43-PB KIT
Locator CL43-PB Kit with rod probe SA05 (512Hz)
- Affordable receiver especially for locating duct sondes
- Also compact wire and cable locator
- Supports 33kHz, 10kHz and 512Hz frequencies
- For outdoor and indoor use
Cable Tracer TM30
- Traces cables and wires, also live wires up to 400V
- Identifies wires and pairs and circuit breakers
- Monitors telecommunication lines
- Locates metal tubes and ducts
COMPACT LOCATOR CL43-PA
LOCATOR CL43-PA Kit with SA43 rod probe (33kHz and 10kHz)
- Affordable receiver especially for locating duct sondes
- Also compact wire and cable locator
- Supports 33kHz, 10kHz and 512Hz frequencies
- For outdoor and indoor use
SA43 – ROD ANTENNA FOR COMPACT LOCATOR
SA43 – ROD ANTENNA FOR CL43 COMPACT LOCATOR, 10 KHZ AND 33 KHZ
TETP-900: Multi-Function Cable Tester Tone & Probe Kit
Kit includes:
- TET-700 Multi-Function Cable Tester & Toner
- TEP-200 Tone Tracing Probe
- TET-6 Accessory Kit for TET-700
- (2) 9V batteries
VT-1000: Non-Contact Voltage Tester 90 to 1000VAC
JONARD
- Non-contact voltage detection from 90-1000 VAC
- Tests wires and cables through insulation as well
- CAT IV 1000V rating for added operation and protection
- LED light and beep sound to indicate that voltage is detected
- Optional silent mode for use in quiet areas
- Compact and lightweight design with built-in pocket clip allows you to carry it on the go
- Automatically shuts off after 3 minutes to preserve battery life
- Powered by (2) AAA batteries (included)
MCT-468: Modular Cable Tester for RJ45, RJ12, RJ11 Cables
JONARD
- Tests RJ45, RJ12, and RJ11 terminated cables with ease
- Tests for opens, shorts, and miswiring
- Full LED indication lights on both main and remote unit
- Automatically tests when switched on
- Can slowdown testing procedure using “S” switch to better see each test
Includes: Nylon carrying case and 9V battery (for use)
DRILL POINT LOCATOR PK2
- For pinpointing drill holes through up to 150cm concrete walls and floors
- For determining required drill depth
- For detecting metal and electric obstacles
COMPACT LOCATOR CL43-PB KIT
Locator CL43-PB Kit with rod probe SA05 (512Hz)
- Affordable receiver especially for locating duct sondes
- Also compact wire and cable locator
- Supports 33kHz, 10kHz and 512Hz frequencies
- For outdoor and indoor use
Cable Tracer TM30
- Traces cables and wires, also live wires up to 400V
- Identifies wires and pairs and circuit breakers
- Monitors telecommunication lines
- Locates metal tubes and ducts
COMPACT LOCATOR CL43-PA
LOCATOR CL43-PA Kit with SA43 rod probe (33kHz and 10kHz)
- Affordable receiver especially for locating duct sondes
- Also compact wire and cable locator
- Supports 33kHz, 10kHz and 512Hz frequencies
- For outdoor and indoor use
SA05 – ROD ANTENNA FOR COMPACT LOCATOR
SA05 – ROD ANTENNA FOR CL43 COMPACT LOCATOR, 512 HZ
SA43 – ROD ANTENNA FOR COMPACT LOCATOR
SA43 – ROD ANTENNA FOR CL43 COMPACT LOCATOR, 10 KHZ AND 33 KHZ
TETP-900: Multi-Function Cable Tester Tone & Probe Kit
Kit includes:
- TET-700 Multi-Function Cable Tester & Toner
- TEP-200 Tone Tracing Probe
- TET-6 Accessory Kit for TET-700
- (2) 9V batteries
VT-1000: Non-Contact Voltage Tester 90 to 1000VAC
JONARD
- Non-contact voltage detection from 90-1000 VAC
- Tests wires and cables through insulation as well
- CAT IV 1000V rating for added operation and protection
- LED light and beep sound to indicate that voltage is detected
- Optional silent mode for use in quiet areas
- Compact and lightweight design with built-in pocket clip allows you to carry it on the go
- Automatically shuts off after 3 minutes to preserve battery life
- Powered by (2) AAA batteries (included)
MCT-468: Modular Cable Tester for RJ45, RJ12, RJ11 Cables
JONARD
- Tests RJ45, RJ12, and RJ11 terminated cables with ease
- Tests for opens, shorts, and miswiring
- Full LED indication lights on both main and remote unit
- Automatically tests when switched on
- Can slowdown testing procedure using “S” switch to better see each test
Includes: Nylon carrying case and 9V battery (for use)